leftthreads.blogg.se - Make grim reaper scythe

Take the thrown property away from the base weapon and put it in a weapon mastery feat like the ones from Unearthed Arcana, and I'd allow it. Now that I've figured out that the brutal property isn't actually a property, but a fancy way of saying that the weapon's damage die is increased, I think it's almost balanced. Just make sure you put a drop cloth or plastic down to protect your floor.Monstrous Compendium Vol 3: Minecraft Creatures

Wait for it to dry, then brush watered down black acrylic paint over the entire surface and wipe away the excess. The Shaft: Spray paint the entire shaft a light brown or tan color to give it a natural look. Also, it’s best to do this the same day you spray the sliver paint, otherwise the paint will harden and be much more difficult to scrape off. If you want to give the blade an appearance that it is beginning to rust, all you need to do is take a tool like the edge of a pair of pliers or a wrench and carefully scrape away some of the silver paint to reveal specks of the brown primer underneath.ĭon’t get too carried away doing this, just a few hints here and there that there is some rust beginning to form. Give the beveled edge a coat of shiny silver acrylic paint for more added realism. This will give the blade more depth, and make it look "used". Once the blade is dry, mix a small amount of silver acrylic craft paint with a small drop of black, and dry brush streaks perpendicular to the edge of the blade. Flip the blade and repeat for the other side. Give the primer at least an hour or two to dry and then spray a couple coats of silver paint.

Wait for it to dry, then flip it over and repeat for the other side. Give the blade a few good coats of brown or rust colored primer. Wrench, pliers or other tool with a blunt metal edge.Spray paint (silver and tan or light brown).Test fit the blade into the shaft and remove more material as necessary until you get a good snug fit. Then use a small chisel and rasp if necessary to clean it up. Use a jigsaw, scroll saw, coping saw, or whatever works to safely remove the material between the two holes. It may be difficult to drill the holes straight through the center using only a hand drill. If you have access to a drill press, that would be ideal for this. Then use a ½” bit, or a bit the same size as your blade width to drill out the pilot holes. Measure and mark out where you want the blade to penetrate the shaft, then drill small pilot holes on each end and make sure they are centered. We don’t exactly want this to look like a square piece of lumber when it’s finished. I hope you didn’t put the sander away because now you are going to need it to smooth out the entire shaft. And since our Grimm Reaper actor will be 8 feet tall (on stilts), I had to splice the 2” x 2” with another to extend it an additional foot and a half. Where I live, I couldn’t find any 2” x 2” ‘s longer than 8 feet. You can make your scythe as long as you want. They might even sell it cheap, so be sure to ask for a discount.

Go to your local lumber yard and select the most bowed 2” x 2” you can find.

Drill press or electric drill with 1/2" drill bit.

There's no need to make it sharp, we just want to give the appearance of an edge. If you're going for realism, you will also want to sand down a bevel for the blade’s edge. Just be careful not to sand through the top layer of the plywood. Next, since we are wanting this to look like metal, use a power sander to get the blade as smooth as possible, Start with a coarse 120 grit sand paper and work your way down to a 220, and then even finer if you want. Remember, (as Norm Abrams would say) "there is no more important shop safety rule than to wear your safety glasses". Once you are happy with the shape and design, cut it out with a jigsaw, band saw or scroll saw. My blade ended up at 3-1/2 - 4 feet long, but you can really do any size or design you want, just make sure to leave the blade’s tang long enough so it can be attached to the shaft. For me, this was one of the more difficult parts of the project, but maybe that's because I'm a perfectionist. You can see from the photos, it took me a few tries before I was finally happy with the design. Use a pencil to draw the blade shape onto a scrap piece of 1/2” plywood.

Electric sander with 120 and 220 grit sandpaper.